Lubricating System Analysis Using the FMEA Method to Determine System Failure

Authors

  • Sabilil Huda Al Hakiki Universitas HangTuah
  • Dwisetiono Dwisetiono Department of Marine Engineering, Hang Tuah University

DOI:

https://doi.org/10.62012/zl.v2i3.18594

Keywords:

FMEA Method, Lubricating System, Maintenance

Abstract

Failure in a component in the lubricant system will have an impact on the operation so a review is needed to overcome the failure of each component and the maintenance of components based on the level of risk. The creation of a risk-based treatment analysis with the FMEA method has several steps that describe the identification and evaluation of the system, process and treatment to determine the treatment strategy resulting from the method. Failure Mode and Effect Analysis (FMEA) is a method of evaluating risks in the system. FMEA can evaluate and analyze components in a system so as to minimize the risk or effect of a failure rate as a method of supporting performance assessment on a system. The use of FMEA methods other than in industrial machinery is widely used also to analyze preventive maintenance planning on ship machines. As a result, the FMEA method can identify the priority of the highest ration stainer component rpn value (Risk Priority Number) compared to other components. This study to determine the failure of each component of the lubricant system in the diesel engine and choose the right type of maintenance for the components. The benefits of knowing the failure and koponent maintenance of the lubricant system will provide benefits to the ship in terms of maintenance..

Downloads

Download data is not yet available.

References

M. Z. Latif A, Y. E. Priharanto, D. Prasetyo, and M. Muhfizar, “Preliminary Hazard Analysis dan Fault Tree Analysis untuk Identifikasi Penyebab Kegagalan Sistem Pelumas Mesin Induk Kapal Penangkap Ikan,” J. Airaha, vol. 7, no. 02, pp. 77–87, 2018, doi: 10.15578/ja.v7i02.94.

M. Danil Arifin, F. Octaviani, and T. D. Novita, “Analisa Kegagalan Sistem Pelumasan dan Pemilihan Metode Perawatan M/E di Kapal Menggunakan Metode FMEA Dalam Rangka Menunjang Operasi Transportasi Laut di Indonesia,” J. Penelit. Transp. Laut, vol. 17, no. 1, pp. 1–6, 2020, doi: 10.25104/transla.v17i1.1416.

G. Y. Nusantara, “Pengaruh Efek Perawatan Terhadap Jadwal Perawatan Sistem Pendukung Mesin Induk Pada Kapal Dengan Menggunakan Pemodelan Dinamik Sistem,” Jur. Tek. Sist. Perkapalan, Inst. Teknol. Sepuluh Nop., p. 130, 2015.

Alwi, “Reliability Centered Maintenance Dalam Perawatan. Jurnal Riset Dan Teknologi Kelautan (JRTK),” pp. 77–86, 2016.

R. B. Manalu, U. Budiarto, H. Yudo, F. Teknik, U. Diponegoro, and M. C. Simulation, “Analisa Perawatan Sistem Distribusi Minyak Lumas Berbasis Keandalan Pada Kapal Km.Bukit Siguntang Dengan Pendekatan Rcm (Reliability Centered Maintenance),” J. Tek. Perkapalan, vol. 4, no. 1, 2016.

M. Saputra, R. S. H., Priharanto, Y. E., & Abrori and Z. L., “Failure Mode and Effect Analysis (FMEA) Applied for Risk Assessment of Fuel Oil System on Diesel Engine of Fishing Vessel. ARPN Journal of Engineering and Applied Sciences,” 2018.

S. Wannawiset and S. Tangjitsitcharoen, “Paper Machine Breakdown Reduction by FMEA and Preventive Maintenance Improvement: A Case Study,” IOP Conf. Ser. Mater. Sci. Eng., vol. 530, no. 1, 2019, doi: 10.1088/1757-899X/530/1/012051.

R. Imanuell and M. Lutfi, “Analisa Perawatan Berbasis Keandalan Pada Sistem Bahan Bakar Mesin Utama KMP. Bontoharu,” JST (Jurnal Sains Ter., vol. 5, no. 1, 2019, doi: 10.32487/jst.v5i1.540.

K. Cicek, H. H. Turan, Y. I. Topcu, and M. N. Searslan, “Risk-based preventive maintenance planning using Failure Mode and Effect Analysis (FMEA) for marine engine systems,” 2010 2nd Int. Conf. Eng. Syst. Manag. Appl. ICESMA 2010, 2010.

J. Inovasi, S. Dan, and T. Kelautan, “Zona laut,” vol. I, no. I, pp. 1–6.

Z. A. Yusuf, “Analisa Perawatan Berbasis Resiko Pada Sistem Pelumas Km. Lambelu,” J. Ris. dan Teknol. Kelaut., vol. 14, no. 1, pp. 129–140, 2016.

R. I. Yaqin, Z. Z. Zamri, J. P. Siahaan, Y. E. Priharanto, M. S. Alirejo, and M. L. Umar, “Pendekatan FMEA dalam Analisa Risiko Perawatan Sistem Bahan Bakar Mesin Induk: Studi Kasus di KM. Sidomulyo,” J. Rekayasa Sist. Ind., vol. 9, no. 3, pp. 189–200, 2020, doi: 10.26593/jrsi.v9i3.4075.189-200.

Published

2021-07-28

How to Cite

[1]
S. H. Al Hakiki and D. Dwisetiono, “Lubricating System Analysis Using the FMEA Method to Determine System Failure”, zonalaut, vol. 2, no. 3, pp. 99-105, Jul. 2021.

Issue

Section

Systems and Control of Marine

Most read articles by the same author(s)